Features

·       Charging current (automatically adjustable) 0,1-5,0 A and 5,0-25 A

·       Charging power: 400 W / 12 V; 800 W / 24 V; 1500 W / 48 V

·       Charging voltage 0,6-64 V; 1-34 NiCd and NiMH; 1-24 Pb; 1-14 Li-Ion; 1-14 LiPo; 1-16 LiFe; 1-20 LiS-ready (balances up to 16s)

·       Supply voltage 12 V (10-16 V); 24 V (20-32 V); 48 V (40-60 V)

·       Powerlimiter for using with a low power power supplies (50-1800 W)

·       Separate setup parameters for usage with car battery and power supply

·       Storage program for charging/discharging to storage voltage

·       Cycles (up to 99): charge/discharge; discharge/charge (current can be set up different between charge and discharge) and format

·       Format with battery regeneration function (NiXX)

·       Permanent measurement of resistance (Ri) while charging (only impulse mode)

·       Built-in balancer up to 16 cells (simultaneous balancing up to 16 cells)

·       Max. balance current 1 A/cell (pre-setup in 4 steps: 0,0 A = no balancing - only display; 0,25 A; 0,5 A; 1,0 A)

·      Balancing only mode (whole voltage range)

·       Balancing power 60 W

·       Balancing current - automatically variable individually in 10 steps per cell  

·       Intelligent balancing algorithm

·       Balancing start voltage automatically ascertainable - depends on height of cell debalancing

·       Balancing funnel-shaped - full cells means more intense balancing

·       Process memory (last processes data): 20

·       Program memory (user settings): 20

·       Charging finish identification (NiXX): Delta-peak (adjustable from 1 to 25 mV in steps of 0,5 mV); Inflex; charging time; adjusted capacity

·       Pb, Li-Ion, LiPo, LiFe - finish voltage of charging +100 / - 200 mV adjustable

·       Fastmod (genuine) for Li-Ion, LiPo, LiFe, Pb

·       Reflex function - (memory effect protection for NiCd & NiMH), lowers voltage drift at LiXX

·       Modes: Impulse, Reflex, adjusted for usage with power supply (Impulse mode off)

·       If not used, zero voltage at output (safety for charging batteries inside of devices, e.g. transmitter)

·       Reverse battery protection (input, output)

·       Lightning arrester for battery connecting

·       Charger housing isolated from earth (minus); no short circuit at housing possible

·       Temperature sensor

·       Step-down/step-up converter for full charging of single cell batteries

·       Discharge process up to 100 W with external mains power supply without additional, external resistors

·       Reverse – returns discharging current to supply accu starting from 4 V

·       Protects supply accu against overcharging (in Reverse mode)

·       Adjustable min. voltage of supply accu 10,5 - 11,5V (protects against deep discharge) 10,0-11,5 V (also 24 V and 48 V)

·       Digital control converter with special digital signal prozessor (DSP: allows fast and precise control)

·       Graphical display 240 x 64 dots

·       Permanent display backlight (brightness and contrast adjustable); reverse display possible (negative)

·       Acoustic alarm (disengageable)

·       Individual configuration on SD card (possible temporary use in other devices)

·       Process logging on SD card (archive and analysis on PC possible)

·       Built-in real-time clock (time will be also logged to SD card)

·       USB connection (cable included)

·       Optional BT communication class 1 (up to 100 m range) with external antenna for communication with PC and smart phones

·       Internal cooling fan with smooth adjusting (very quiet - only one fan)

·       PC Software (bundled with charger )

·       SD card included

·       Free upgrades over internet

·       Small (No external radiator)

·       Prepared for wireless battery identification (inductive)

·       Prepared for two-way communication with PDA and mobile phones using BT (class 1)

 Prices and order:

Professional Charger Pulsar 3 - Item. No.: 1234  € 589,- (incl. 19% VAT)

BT additional module for Pulsar 3 (incl. installation and antenna - only if purchased together with a new Pulsar 3 charger) - Item. No.: 1253  € 40,- (incl. 19% VAT)

BT additional module for Pulsar 3 afterward installation (incl. installation and antenna) - Item. No.: 1235  € 65,- (incl. 19% VAT)

Balancer adapter UNI (EH) for Pulsar 3 - Item. No.: 1236  € 29,- (incl. 19% VAT)

Balancer adapter XH for Pulsar 3 - Item. No.: 1237  € 29,- (incl. 19% VAT)

Accupack cable incl. temperature sensor for Pulsar 3 - Item. No.: 1305  € 9,- (incl. 19% VAT)

Industrial power supply MeanWell SPV-1500-48 - Item No.: 1268  335,- € (incl. 19%% VAT)*

* as set with Pulsar 3 charger (Art.Nr.: 1234) - 10% = 301,50 € (incl. 19% VAT)

Industrial power supply MeanWell RSP-3000-48 - Item No.: 1256  569,- € (incl. 19%% VAT)*

* as set with Pulsar 3 charger (Art.Nr.: 1234) - 10% = 512,10 € (incl. 19% VAT)

Main cable 2m, grey - Item No.: 1239  3,90 €  (incl. 19% VAT) Necessary for power supply

App for Android by Thorsten Wruck The App for for managing events such as flights, charging and discharging, model planes and batteries can now also display the values of Pulsar 3 when charging or discharging a battery and add an event. The app can be obtained from AndroidMarket under the name RC-Heli-Battery Flight Log.

Ordering will be easier with our prepared PDF form. Please complete the form, save it to your disc and send it as email attachment or print and send by fax.

To place an order please send any enquires by e-mail to:  or by fax: +49 4121 750676

Attention, we are looking for dealers for ELPROG Pulsar chargers and pp-rc Modellbau products in all countries!