Mainpage Infos & Ordering Terms & Condition DE Version

 

Charge power 350 W, current to 12 A !

 

TEST BY: SchiffsModell 5/2009; "Modell Flieger" August-September 2009

  • Charging voltage 0,5 - 60 V (1 - 32 NiCd, NiMH; 1 - 18 Pb; 1 - 26 RAM, 1 - 12 Li-Ion, 1 - 14 Li-Ph; 1 - 12 Li-Pol; 1 - 12 Li-Ta

  • Charging current 0,2 -  12 A

  • Charging finish identification: Delta-peak (adjustable from 4 to 25 mV in steps of 0,5 mV); Inflex; charging time; adjusted capacity; temperature sensor

  • Process memory (last processes data): 8

  • Program memory (user settings): 8

  • Reflex function  - ( „memory effect” protection for NiCd & NiMH)

  • Geeignet für: NiCd, NiMH, Pb, RAM, Li-Ion, Li-Ion FePO4, Li-Pol, Li-Manganoxide (Tadiran)

  • Charge; Discharge; Discharge-Charge; Charge-Discharge  (up to 350W)

  • Fast Mode Li-Ion, Li-Pol, Li-Ion FePO4, Pb (to 12 A) COMPARISON Fastmod to standard charging: ca 32 % time saving at modern low-resistance cells!

  • Pb, RAM, Li-Ion, Li-Pol, Li-Ion FePO4, Li-Manganoxide (Tadiran) - finish voltage of charging +100 / - 200 mV adjustable

  • Data communication with Pulsar EQUAL (balancer)

  • Step down / step up converter makes possible full charging current for single accus

  • Format with battery regeneration function

  • Store - Programm for charging / discharging to storage voltage

  • Reverse – returns discharging current to supply accu starting from 3 V

  • Protects supply accu against overcharging (in Reverse mode)

  • Adjustable min. voltage of supply accu 10,5 - 11,5V (protects against deep discharge)

  • Powerlimiter for using with a low power power supplies

  • Discharge process up to 50 W with external mains power supply without additional, external resistors

  • Accurate internal resistance measurement of battery  (Ri – up to  6A/50W)

  • Fully protected against wrong connecting (input, output, cooling fan)

  • Display with permanent backlight

  • Acoustic alarm (disengageable)

  • Internal cooling fan with smooth adjusting (very quiet)

  • PC Software (bundled with charger )

  • RS232 cable for PC (bundled with charger)

  • Free upgrades over internet

  • Small (No external radiator)

 

 Changes compared to the Pulsar 2

 

- 350 W power and 12 A (250 W 9,9 A)
- Discharging without reverse – 50 W (35 W)
- Charge- Discharge end-voltage justable (+100 mV -200 mV) (only charging voltage -200 mV)
- Delta by NiXX justable (NiCd 4-25 mV, 8 mV standard; NiMH 1-15 mV, 4 mV standard) (Delta low & high with permanent voltage)
- Automatic storage function  (no storage)
- Upgrade via Internet (RS) (no possible)
- Powerlimiter (starting at 50 W) at input (not possible)
- Test (Ri) 6 A 50 W (4 A 35 W)
- Format into 6 A (4 A)

Description:

 

PULSAR 2+ is a fast, microcontroller-based charger suitable for use with various types of batteries. Special design of hardware and software makes it possible to charge batteries with high currents without risk of damage and in some cases even improving their durability. During charging process all important parameters are displayed on LCD and transmitted via serial port (RS232) to a desktop computer. Additional software allows visualization of changes in voltage, current, voltage time derivative and temperature during whole charging process which allows user to determine precisely status of batteries and decide whether they need conditioning or not. A data communication between Pulsar 2+ and Pulsar-EQUAL Equalizer (Balancer) is possible and increases the safety of working with Li-Xx packs. Firmware of Pulsar 2+ can be updated via serial port.

  

 Technical data

 

Supported accu types

NiCd, NiMH, Pb, RAM, Li-Ion, Li-Ion FePO4, Li-Pol, Li-Manganoxide (Tadiran)

Supply voltage

10 – 16 V (car battery min. 30 Ah – recommended 70 Ah or power supply 14 V/60 A (min. 10 A)

Low voltage alarm level (and switch off)

Min. 10 – 11,5 V, max. 16V (adjustable in Setup menu)

Charging voltage

0,5 – 60 V (1 – 32 NiCd)

Charging current

200 mA – 12A (350 W)

Discharging current

200 mA – 12A (250 W) with energy return

200mA – 12A (50 W) with heat dissipation

Temperature measurement

0 – 99° (accuracy 0,1°C)

Voltage measurement

0,1 – 60 V

Current measurement

0,1 – 14 A

Timer

14 h

Max voltage on supply battery

Reverse - ON 15,3 V

Dimensions

130 x 120 x 58 mm

Weight

750 g

 

Pulsar 2 / 2+ - Display

Download (Adobe pdf)

 

PC- Software V2.40 - DOWNLOAD

Pulsar-Firmware V10E - DOWNLOAD

 

Instruction englisch Version v10

Instruction deutsch Version v10

 

Prices and order:

 

Charger Pulsar 2+ - Art.No.: 1125  € 299,- (incl. 19% VAT)

Pulsar remote  - Art.-No.: 1132  € 99,- (incl. 19% VAT)

Pulsar remote enables the remote control of the processes of Pulsar chargers or a wireless connection from a Pulsar charger to the PC/notebook. In this way you can charce your accumulator in the car while drinking limonade in the club house. Of course without losing the charging process out of sight! Even if you charge your packs in the cellar, you can watch the process from your living room. Both parts are upgradable by the internet.

In future it will be possible to transfer data wireless from the Pulsar-EQUAL to the PC with the Pulsar remote.

Further information and service data can be found at the manufacturers homepage.

To place an order please send any enquires by E-Mail to:  or by Fax: +49 4121 750676

 

Attention, we are looking for dealers for ELPROG Pulsar chargers and pp-rc Modellbau products in all countries!